What Are Brass Non-Return Check Valves?

In this blog post, you’ll read:Among the different materials in which valves are available. Brass is one such material that applies widely to its alloying material properties. The brass check valve is made of chromium and carbon alloying components. These materials provide the valve with distinct properties. The manufacturer of brass check valves proposes these valves due to corrosion resistance.
Table of Contents

What Is Brass Check Valve?

Among the different materials in which valves are available. Brass is one such material that applies widely to its alloying material properties. The brass check valve is made of chromium and carbon alloying components. These materials provide the valve with distinct properties. The manufacturer of brass check valves proposes these valves due to corrosion resistance. The brass one-way check valve shows qualities such as;

  • Ductility
  • Durability
  • Stability in high pressure
  • High toughness

Brass Check Valves are also called non-return valves or one-way valves. A valve allows fluid (liquid or gas) to flow in only one direction. There’s a brass spring check valve, foot valve, and swing type. A brass check valve is installed in the pipeline to filter impurities of the flow Y shape type. It is used in residential premises and for commercial applications.

The brass check valves permit the fluid to stream in a single direction. Yet, it stops the flow of fluid in the backward direction. The backflow causes contamination or damages the other parts. It works and is not required to operate. The majority of available kinds have little spring to close the valve. The medium pressure involves opening the valve in the forward direction.

From R.C. Worst & Co., Inc.

Classification of Brass Check Valves

1) Swing Check Valve

The check valve mounts on a horizontal pipe with a vertical centerline of the valve body. The ball can be used on a high-pressure diameter check valve. The shape of the valve body of the lift check valve is the same. It is the shut-off valve used with the globe valve. Its fluid resistance coefficient is too large.

The lower part of the bonnet and upper part of the flap valve machine with the manual sheath. The valve guide can be lifted in the valve guide. When the medium flows downstream, the valve flap opens by medium push. When the medium stops, limp down on the base from the media to stop the countercurrent effect. There are two kinds of brass swing check valves

Swing Non-return Check Valve 0618e
Swing Non-return Check Valve

2) Brass Spring Check Valve

The Brass Spring Check Valve is also referred to as a reflux or clack valve. It is an automatic and self-acting valve that helps flow in a single direction. It also prevents backward flow. It has a single outlet and inlet with proper orientation to do functions. Yet, an arrow shows the flow direction on one side of this valve. The brass spring check valve is suitable for various industrial and domestic purposes. It has the following kinds;

  • Brass Inline Spring Check Valve

In various applications, it prevents reverse flow contamination by pressure pipes. This valve applies where the tank system joints with primary water. It needs to stop the backflow.

  • Ball Spring Check Valves

The ball spring check valve uses the ball. It closes the seat located near the inlet orifice. It shifts when the cracking pressure from the flow is greater than the spring. Yet, it keeps the ball and flows and passes through. When the cracking pressure reduces, the spring moves the ball to near the inlet.

To Buy the spring check valve.

vertical check valve
vertical check valve

The Difference between the Other Check Valve and the Brass Check Valve.

Other brass valves are valve-like brass radiator valves, brass angle valves, and brass gate valves. These valves have a different function and mechanism than a brass check valve. Yet, they are also crucial for pipelines.

Applications of Brass Check Valves:

A brass check valve has impressive properties for applying water, air, and oil. However, it is not suitable to resist chlorinated and seawater. It is more resistant to corrosion and heat than stainless steel. It also has corrosion-resistant properties over steel and carbon. It prevents the water from streaming back. It always keeps the water supply line full of water.

The reason behind utilizing the check valve is to forestall the media reverse. For the most part, the siphon opening costume with an authentic look at the valve. In the blower opening, instruct them to look at the valve to put it.

A check valve is used to clean the streaming medium. It should not be used for solid particles and sticky liquid medium. The check valve open isn’t light. Close the seal isn’t dependable.

The fluid back isn’t reliable. Its absolute position is to forestall the media back to forestall—the siphon and drive engine inversion and compartment media release. The check valve can be used directly where the strain might exceed the supply framework that betters the pressure.

swing check valve
swing check valve

How Does this Valve Work?

This valve has two ports—one port for the media and the other for the out of the media. The main aim of this valve is to stop backflow in the system. It also refers to one-way valves. It passes the media flow only in a single direction.

This valve relies on pressure differential to work. Opening the valve requires higher pressure on the inner side than the outer side. The valve will close when the tension is higher on the exterior (output side). Depending on the valve kind, the closure phenomena are different. Distinct other valves do not need an actuator, handle, lever, or human to work.

It installs where the backflow creates problems. Yet, they are non-return valves, effective, less expensive, and easy solutions to end the problems. The reverse flow creates an issue if the backflow contaminates. Therefore, they contaminate media upstream. For instance, a sewer line will have a non-return valve. It ensures that waste can leave yet not reappear in the framework. It is like use assuming the release will damage equipment upstream. It can permit media to stream in one approach.

For instance, a converse assimilation drain can have water go through it in one direction. So, a one-way valve is introduced downstream to forestall this. Different sizes, plans, and materials ensure a brass check valve for each application.


From SupplyHouse.com

What sizes of brass check valves?

DN15,DN20,DN25,DN32,DN40,DN50,DN65,DN80,DN100

1/2inch, 3/4inch,1inch,11/4inch,11/2inch,2inch,2-1/2 inch,3inch,4inch

Size1/2” to 4”
ThreadBSP, NPT, BSPT
ConnectionThread, Flange end
Cracking pressure0.5 Bar
Pressure rating180PSI, 200PSI
Check valve specifications

What are the working pressures of the brass check valve?

0 to 18 BAR 0°C to 80°C from DN15-DN50

0 to 20 BAR   0°C to 80°C from DN50-DN100

Brass Check Valve Price

The cost of a brass check valve varies from size to size and material. A brass double-check valve is another valve, a brass body with a compress and screw connection. However, the temperature sustained by these valves ranges from 0 to 100 degrees. These valves have high-pressure ratings ranging from 0 to 10 bars.

Advantages of Brass Check Valve

  • Capable of handling additional weight of piping fixing.
  • Fast closing
  • No direct metal-to-metal sealing.

Brass check valves have distinctive properties for air, water, oil, or fill applications. In any case, it isn’t impervious to seawater, filtered water, or chlorinated water. They are used for more modest applications with low pressure.

spring check valve
spring check valve

Problems with the Solution of Brass Check Valves

The middle of the valve is not perpendicular to the horizontal plane. That’s why the valve flap is not flexible. It affects the closing and opening of the valve, which is not good. In this case, a check valve is also installed to turn it into a normal working state. The installation should pay attention to the stream of fluid. So, the valve closes automatically in case of reverse flow of fluid. The sealing surface of this valve harms the valve leakage—the emergence of components of fluid reflux.

Frequently Asked Questions

Why is my valve not working?

When it does not work, it allows it to flow backward. Three primary reasons for this are;

  • Leakage
  • Sticking
  • Slow Closing

Consider there is no filter in the line, and debris and dirt tap among the body and disc. Keep it open due to corroding media on the material, preventing a proper seal and permitting backflow. Consider the valve closes too slowly, and backflow enters before a good seal occurs. Make sure the gravity helps the structure. Or your spring is fast enough to shut the valve.

Bronze swing check valve spare parts and size
Bronze swing check valve spare parts and size

What orientation should a valve install?

It needs to be installed according to its outlet and inlet. It is frequently offered as the arrow on the valve housing. If they are installed backward, they will not work. Omit vertical or horizontal if you rely on your valve design kind. If it is spring, any orientation is acceptable. If there is no spring, gravity affects the valve working. So, install the inner parts properly, vertically or horizontally.

How to Prevent Brass Check Valve from Failing?

The major disadvantage of this valve is the difficulty of determining the condition of the enclosed valve. So, there are essential measures to understand their failure and prevent it. Various indicators like a potential failure,

· Measure reverse flow,

· Audible indications of leakage,

· Excessive parts wear

You can avoid loss by:

· Routine checking for cleanliness

· Proper sizing

· Proper installation

· Replace valve needs

It plays a vital role in controlling flow with high-performance systems. Choosing the suitable valve offers a more incredible piping system. It operates efficiently and improves safety.

top brass check valve
top brass check valve

Essential Things to Consider While Choosing the Valve

Some important things are critical before selecting the brass check valve. It is necessary to choose your valve, respecting the characteristics of each specific installation. These areas follow;

· Flow Characteristics

· Fluid

· Non-Slam Characteristics

· Cost

· Head Loss

Solutions For Waterworks Plumbing

Get quote Now

Free Sample with OEM