Brass Shower Drains

Parameters of Brass Shower Drains

Shower drain,Socket, Equal Union, Equal Elbow, Equal Tee, Female Elbow, Female Tee.

Additional information


Brass, CW617N, H58-3





Thread connection



4-1/2 inch, 4"




36 months

Details about Brass Shower Drains

Brass Shower Floor Drain


Shower Drain with Stainless Steel Strainer, 2-Inch
Secures to an sch. 40 DWV pipe with a compression gasket
Compatible with 4-1/2 in.
Brass drain body and stainless-steel strainer
Secures to an sch. 40 DWV pipe with a compression gasket (pipe and gasket not included)

Brass and stainless steel cover

How to use the Brass Shower Drains?

2 0 Plain Cone Drill bit is recommended for use with thread inch Drains or smaller The first step in installing your new drains will be to put one end into an open area where there are not already any pipes going around it, then stick the other side upwards so that both fit inside each other securely like puzzle pieces together making sure they’re flush before pushing firmly until you hear/feel a … 3) Place cone-end down against overflow pipe baseboard (or place either alone depending upon design preference). 4.) Screw the collar onto the drill motor securely and turn the thumbwheel clockwise until tight.

Different ways to use your brass shower drain, depending on your need. One way is just like any other drain – if it’s clogged and requires unblocking, then run hot water from a tap or stand upright in an overflowing sink until the obstruction has been removed ( Be careful not to let too much liquid come out). Another idea would be using one as part of a romantic date night by filling up both tanks with cool water before turning off the main plumbing supply line at the wall & adding sealant around the edge where two pipes meet; Brass shower drains can be a great way to prolong your home’s water pressure and increase satisfaction in the bathroom.
The first step is installing new pipes from where it comes out into another room, such as under flooring or behind walls, before running them back down again outside any building material that might block its path (like concrete). You’ll also have to replace old ones if they’re badly bent around sharp turns – though typically, only two pieces are needed per turn, according to our experts.

The best way to use brass shower drains is by following these instructions. First, you must measure the distance between your drain and curb height so that it can be cut at an appropriate level for installation without exposing any unnecessary parts or causing obstructions in pipes below ground level when installed correctly by a professional plumber who knows what they’re doing! Next, remove one side plate from each pipe with both hands while pushing down until there’s enough space left within which to stretch out equally dividing lines along their length; do this across both pieces, then reassemble them again – now place against a wall where desired before replacing other fixture hats/caps, etc.

Benefits of Brass

Brass shower floor drains offer a variety of benefits when compared to other materials used for the same purpose. Homeowners looking for a durable and aesthetically pleasing alternative to traditional plastic or chrome floor drains should consider brass showers. Not only does brass look elegant, but it is also highly resistant to corrosion and rust, making it perfect for bathrooms that experience high humidity levels.

Also, brass is a solid material that can withstand heavy usage without requiring frequent repairs or replacements. This makes it an ideal choice for busy homeowners who don’t have time to maintain their fixtures constantly. Brass shower floor drains are easy to clean and rarely require additional maintenance beyond routine cleaning. Furthermore, this drain has the added benefit of blending in with virtually any bathroom decor theme due to its neutral coloration and timeless design elements.

What is a Floor Drain?

A floor drain is an essential component of any home that helps keep the indoor environment safe, healthy, and sanitary. It is a device used to collect water from showers, sinks, laundry rooms, and other areas where there might be standing water. Floor drains are typically made from plastic or metal and come in various designs.

One type of floor drain is the brass shower floor drain. This device is designed with a chrome-plated finish and is a stylish option for modern bathrooms. The brass construction can withstand rusting and corrosion over time, making it an ideal choice for long-term durability. Not only does this type of drain look great, but it also functions efficiently to help keep your bathroom clean and dry by quickly disposing of water buildup.

Advantages of Brass Drains

Brass shower floor drains are an excellent option for upgrading their bathroom’s aesthetic with an elegant and sophisticated look. Not only does brass provide a stylish appearance, but it also offers several practical advantages compared to other materials.

The first advantage of brass drains is that they are highly durable. Brass is known for its strength, allowing it to withstand regular wear and tear for many years without requiring additional upkeep. This makes brass drains perfect for high-traffic bathrooms or wet areas where drainage performance needs to be reliable. The material is both corrosion-resistant and temperature-resistant so it can handle heavy use without any problems.

Finally, brass drains require minimal maintenance to keep them looking great. The material is easy to clean since it has antibacterial properties that help prevent the buildup of dirt and grime over time.

Installation Tips & Tricks

Installing a brass shower floor drain can be daunting, but it doesn’t have to be. You can make the installation process smoother and easier with a few tips and tricks. Preparing the area for installation is essential to remove any dirt or debris that may interfere with the drain placement. Make sure to measure twice before cutting your pipes, so you don’t have an uneven fit. Additionally, ensure that all your materials are in good condition before using them to prevent leaks or other issues.

If possible, use flexible plumbing pipes, as they will make it much easier to connect pipe sections without cutting them. Once everything is connected correctly, use sealant on each joint for added protection against water damage.

Maintenance Steps for a Brass Drain

Brass shower floor drains make a stylish addition to any bathroom setup. These drains come in various shapes, sizes, and finishes and are designed to withstand years of heavy use. But proper maintenance is needed to keep them looking their best and functioning properly. Here are some essential steps for maintaining your brass drain:

First, it’s essential to keep your brass drain clean. Regularly remove any soap scum or debris collected around the drain with a soft cloth or sponge. Mix equal parts white vinegar and water, then apply this solution with a soft brush or cloth to remove any stubborn stains from the surface of the brass drain. Rinse away the mixture once it’s done its job.

You should also ensure that you regularly lubricate your brass drain components.

Cost Comparison with Other Materials

Brass is an excellent choice when considering the most efficient and cost-effective option for a shower floor drain. This sturdy material is one of the most robust and durable metals available while being more affordable than other options like stainless steel. The long-term costs associated with brass are much lower than those of other materials regarding installation and maintenance.

Due to their lighter weight and more straightforward setup, brass shower floor drain installation costs are up to 40% cheaper than those for stainless steel or copper drains. Most of the cost associated with installing a brass shower floor drain comes from labor; however, this can be further reduced by opting for a pre-made model or purchasing all necessary parts in bulk. Also, since brass resists corrosion better than other metals, it won’t require costly repairs or replacements as often as other materials.

Conclusion: Best Choice for Longterm Durability

The brass shower floor drain is ideal for homeowners looking to protect their bathroom from water damage and make it more durable. This drain is designed to last long, even with regular use. It has superior corrosion resistance and other wear-and-tear types that can cause problems for different kinds of showers.

Brass also offers excellent longevity since it has been used in plumbing fixtures for centuries. The material is known for its strength and durability, so it can withstand daily wear and tear far better than plastic or metal alternatives. Also, brass won’t corrode like other metals, making it a great choice if you want long-term durability in your shower floor drain.



water pressure gauge

Metals Vavles Works on Plumbing System

Plumberstar valve fabricator in China. Our main parts for heating pipelines and intelligent water control can supply you with a one-stop basket solution to get your ideas and demands. From design to packaging and logistics are our duty—brass valves and fittings applied in-house, in industry, and commercial construction, in residential. There are related to water pipe control solution, and we have rich experience for outdoor frostproof hydrant and pex heating water manifold indoor.

The Top Standard Valves

Plumberstar ball Valve is with CW617N and Lead-free original brass. And water flows with 2pc full Port 400WOG and 600WOG standard to design it with heavy-duty. EPDM and NBR sealing washers are environmentally friendly, with Three years warranty with traceability.

Woman's hand closes the valve. Saving Water Consumption Concept
  •  Plumberstar Valve Made from brass and stainless steel 304, and sourcing HPVC ball valve
  • Connected from the thread with BSP(G) and NPT by the normal.
  • Size with MaleXFemale 1/4inch,3/8 inch,1/2inch,3/4,1inch,1 inch,1-1/4 inch,1-1/2 inch,2inch,2-1/2inch,3inch and 4inch.
  • The actuator of electric valve voltage 24V DC and 230V AC
  • Shut-off needle valve can manufacture based on requirements
  • Heating floor manifold with 1-inch gauge and flowmeter
  • Brass nipple, elbow, extension, compression fitting, adapter available

Plumberstar Valves Applications

y drain strainer

Y-filter Strainer Drain Valve

Plumberstar Y filter strainer Keeps Working, and dirty Out Strainer screen catches debris and sediment to reduce maintenance. Protect your water plumbing. Y Type Strainer works in conjunction with your backflow preventer and regulators.

water tanker safety valve

Safety Water Solution

Plumberstar works in residential, irrigation, and commercial application. The relief safety valves are used in various applications, such as water heaters, air compressors, its automatic release of the excess pressure or vacuum from a heating system.

thermostatic valve pump mix water control

Temperature Mixing Valve

Mixing water valve automatic ensure temperature and water pressure stable. It is suitable for household hot water devices equipped and floor heating, so the 3-way valve meets requirements of temperature range and the water flow

radiant pex manifold 12 connector adaptortubing

PEX Heating Manifold

Plumberstar radiant pex manifolds are usual for residential water distribution in a household, and it's top rated in the home building industry. Manifold plumbing systems control hot and cold water that feeds flexible PEX supply lines to individual fixtures.

Advantages of Plumberstar

Plumberstar products design based on simple structure aim to time-saving installation for consumers and aim to save the cost of customers for building construction.

Play Video about torsion data

We boast 15 years of expertise in water and gas projects and long-term partnerships with top global clients.

We offer competitive pricing, tailored solutions, and flexible solutions. Quality is our cornerstone. We conduct three random inspections and a final QC check for each project, with detailed reports for clients and a 48-hour emergency response system.

Customize-Design Brass Copper Fitting

Copper Pipe fitting 1/2 inch 90-degree Elbow, nipple, bush, and reducer connects PEX Pipe in water distribution and hydronic heating systems.
Low-cost solution to connect copper Pipe Tubing, stainless steel insert, and adapter. The connection system is perfect for your next commercial or homeowner plumbing project.
Brass fittings are made of lead-free and CW602N for durability and corrosion-resistant quality and performance.

brass fitting machine

Advantages for distributer, wholesaler, Supermarket and Trading

Plumberstar is looking for long-time cooperation with partners, our advantage will benefit each other, and growing together, our extra service including design, new tooling, discount and quality tracing system.

★ Moderate Pricing – Plumberstar can provide various projects with different economic basket services. Water control project drawing design and artwork works are free. 

MOQ and Delivery – Lower MOQ even reaches 100 units and sampling time within 15 working days, and the leading time is 30 working days of mass production,

Non-Disclosure Agreement – Plumberstar will not provide your competitors with the same valves and manifolds. And help you to get more market shares.

Quality and Service–Our defect rate reached 0.459% in the last two years from customers feedback, and the Inspection report can provide you with each order

working of a gas shut off valves

Discount and Quantity– Heavy quantity can increase production capacity with effectiveness. And the accessories and spare parts purchased with competitive cost of valves.

Plumberstar Extra Service

Our aim is not only to provide valves but we help customers to design products,design artwork,valve proposal, book shipment,Installation tutorial

Design Valves For House

Valve Project Designing

We are free design your valves according to your inquiry of your plumbing system,no extra cost.

project discussion

Plumbing Control Proposal

We can help you choose valves and heating manifold, and advice in house application

Fix ball Valve

Fluid Control Installation

We can provide an installation guide and tutorial about valves and underfloor heating manifold

loading container

Shippment Service Solution

We help customers to book a container, documents preparation, and clearance, even to warehouse

Frequently Asked Questions

Here are typical questions by customers asked with usual, please feel free contact us if any further confused.

Brass valves have many different types, such as ball valves, garden tap, check valve, strainer, angle valve, gate valve, foot valve, and drain valve. The radiator valve and thermostatic mixing valve are works for water temperature. All of these valves are work for water plumbing systems, plumbing repair, and installation. So have to let water shut-off and shut-on. Some heating systems are related to hot water and cold water mixing for temperature control and stability. Our intelligent valves are functional. There are applications in commercial, residential, and industrial areas.

Underfloor heating radiant pex manifolds are usual for residential water distribution in a household, and it's top-rated in the home building industry. Manifold plumbing systems control hot and cold water that feeds flexible PEX supply lines to individual fixtures. Then water temperature is warm and stable in each room. Meanwhile, the heating accessories-flow meter gauge will monitor water and temperature in each room.

The motorized ball valve works automatically open and closed; they work with 220v-230v AC and 24v DC; they are applications in the heating system, air conditioner,3D printer, and others. The solenoid valve is with similar features.

Would you please submit the form at the bottom of the page or send an email My WhatsApp: +86 15968648802. Can you send us pressure demands, size package, and quantity if available?

It's able to provide free samples for your evaluation with 15 working days about.

Our MOQ is significantly lower from 100-5000 pcs are available. It depends on different items.
We can fabricate your specified requirements.

It's about 35 days if with regular proucts; New tooling and samples will take 15-20 days, Normal samples will take 7 days.

It means that you need to check the plumbing system at first, then realize your requirements, and get out different valves with different applications and functional with controlling; of course, may be no need to use brass valves due to the high cost. You can use plastic, iron, zinc alloy, and aluminum raw materials instead of brass, but brass and stainless steel are reliable with 3 years warranty. If you don't know how to choose, please call us or email us.

An Instant Quote With Specific

There are 5 engineers and 15 experts about QC&QA behind your projects

Why Choose Plumberstar?

Brass is a highly durable material for valves that can withstand temperatures and pressure. It is also corrosion-resistant, making it an ideal choice for wet environments. Brass valves are also easy to clean, an important consideration for plumbing systems. We manufacture brass valves, which are two-piece brass ball valves with 600 and 400-WOG threaded ends that are not for use in potable water.

Let's discussion your upcoming water control parts?

Simply describe your request and details; our feedback within 24 hours

Get quote Now

Free Sample with OEM

× How can I help you?